2004 MAZAK INTEGREX 200-3ST

Fusion Control
Serial Number 173717
Cutting Hours Approx. 7618
Includes a chip conveyor, leveling pads, and  manuals. As well as live tooling for the lower turret





Specifications:
Chuck Size 8"
Maximum Swing 26"
Swing Over Cross Slide 26"
Swing During Y-Axis Process 19.7"
Bar Work Capability 2.55"
Maximum Machining Length 40"
Maximum Support Weight 660 lbs.
Rotating Speed 35 - 500 RPM
Through-Hole Diameter 2.99"

Additonal Specs Can Be Viewed In The Photos For This Machine

Location: Cleves, Ohio
Rigger Will Be Required To Load, Buyers Responsibility

2006 MAZAK VCN 510C II VERTICAL MACHINING CENTER

Serial Number 189150
Matrix Control
Cutting Hours Approx.  17,836
Includes leveling pads, manuals, chip conveyor, pallet changer, Renishaw probe

Renishaw tool setter does not work



Specifications:
Table Working Area Right and Left 51.18"
Table Working Area Back and Forth 21.65"
Saddle Back And Forth Stroke Y-Axis 20.08"
Table Right And Left Stroke X-Axis 41.34
Spindle Head Up And Down Stroke Z-Axis 20.08"
Spindle Nose Taper No. 40
ATC 30

Additional Specs Are Located In The Photo Gallery For This Machine

Location: Cleves, Ohio
Rigger Will Be Required To Load, Buyers Responsibility

Serial# 11E730102
ASSET#339

10 station turret
Tailstock
Turbo chip conveyors that are aftermarket.
Swing over bed 23.6"
Max turning dia...16.5"
Max turning length....60.2"
15" chuck
A2-11 spindle nose
30 HP
2000 RPM
Max 4.6" bar capacity
Wt 19,800#
Tool Presetter

Location: West Alexandria, Ohio
Rigger Will Be Required To Load, Buyers Responsibility

Serial# 11E730098
ASSET #335

10 station turret
Tailstock
Turbo chip conveyors that are aftermarket.
Swing over bed 23.6"
Max turning dia...16.5"
Max turning length....60.2"
15" chuck
A2-11 spindle nose
30 HP
2000 RPM
Max 4.6" bar capacity
Wt 19,800#
Tool Presetter




Location: West Alexandria, Ohio
Rigger Will Be Required To Load, Buyers Responsibility

2013 COSTA MD6-CV+V 1350 SANDER

Equipped with the following working units:
C250 + XVS-85+ XVSi-85

General technical data:

• Useful working width mm 1350
• Longitudinal sanding belt length mm 2620
• Width of longitudinal sanding belts to obtain maximum working width W. + mm 30
• Sanding belt introduction side (standard) Left hand
• Sanding belt oscillation system with electronic photocell - complete with safety micro-switches to stop the machine in case of abrasive belt breakage/mistracking, and a timed activated air jet blower for photocell automatic cleaning.
• Standard working thickness mm 0,8 ÷ 160
• Constant pass-line height of feed table from floor mm 900
• Lifting/lowering of the head with the working units with motorvariator, power kW 0,37
• Rubber-covered roller, positioned in front of machine; is connected to emergency switches; activated it causes the stop in emergency and the thickness opening to prevent damages. Auto-Set - Automatic thickness positioning system with decimal accuracy

Leblond-Makino A55 Fanuc 16M (Pro III)
Serial Number LM-203
New 1992





Specifications:
Pallet Size / Number of Pallets 15.76" x 15.76" / 2
Table Indexing 1 Degree index
Table Load Capacity 880 lbs
Maximum Workpiece Size 23.6" x 27.6"
X-Axis Travel 22"
Y-Axis Travel 22"
Z-Axis Travel 22"
Spindle Nose CAT 40
Spindle Speed 12,000 RPM
Spindle Motor 25 HP
Tool Magazine Capacity 40
Position ATC Tool Change Time 2 seconds tool to tool, 4seconds chip to chip
Rapid Traverse 944 IPM
Machine Dimensions 148"x128"x111.5"
Machine Weight 19,841 lbs

Equipped with:
Coolant-through–spindle (300psi)
Chip Conveyor
1 Deg. Indexing
Rigid Tapping
Helical Interpolation
RS-232
2 Pallet Changer
All Available Manuals Machine has been completely refurbished and repainted by professional rebuild firm. All components have been cleaned and tested, and replacements made where necessary. Reconditioned ball screw covers were installed. The spindle was recently replaced by previous owner and checks good and runs very well.

Location: Cincinnati, Ohio
Will be loaded  at no charge to the buyer

New 12/2012
S/N: 94020
Manufactured Bar Capacity: 0.25" - 3.125"
Maximum Bar Length: 60"
Storage Capacity (1" Diam): 30 Bars Approx.
Machine Dims: 100" X 60" X 50"
Approx. Machine Weight: 1,700 Lbs

Current owner stated they purchased the unit new in 2012 and only used it once for a short run job that only ran for a few days.

600 TON CLEARING STRAIGHT SIDE PRESS
MODEL F4-600-108-60
20” STROKE
46” SH
108” x 60” BA
16 SPM
CUSHION.

PRELIMINARY SPECIFICATIONS:
USI CLEARING STRAIGHT SIDE PRESS
PRESSROOM ELECTRONICS CONTROL PACKAGE
MODEL F4-600-108-60
TOLEDO LOAD MONITOR
S/N 47-13652 HYD.
CLUTCH/BRAKE (MIDWEST BRAND)
600 TON CAPACITY
T-SLOTTED BOLSTER AND RAM
20” STROKE
CUSHIONS, 60 TONS, 10” STROKE, 46 X 46 PAD AREAS
46” SHUTHEIGHT (SDAU OVER BOLSTER)
DIE LIFTERS/ROLLERS IN BOLSTER, WITH SIDE MOUNT
108” LR X 60” F-B
CONSOLES
16 SPM
WELL-MAINTAINED, IN RUNNING CONDITION.

LOCATION: COLDWATER, OH.
Rigger Will Be Required To Load, Buyers Responsibility

MIDWEST SANDRIGHT FINISHING AND DEBURRING MACHINE
Model D-52
Serial Number is 2624-0512
This sander has been used approximatley 5 hours on mild steel



The machine would come with discs, finishing and deburring pads, and a paper bed filter

Machine dimensions:  (L)103"x(W)93.25"x(H)125". 

The material capacity is a 52" working width

Location: Cleves, Ohio
Rigger Will Be Required To Load, Buyers Responsibility

2000 EUROMAC CX1250/30
Serial Number: MDC128012A

Specifications

Dimensions are (L) 125.5"x(W)154"x(H)70".

Max sheet metal gauge is 11 gauge.

Max travel: X= 80.59" Y= 48.81" 

Eurowin Control, Version 5.36
Working Hours Approx. 2,500

The screen on control does not work.  They use a Dell computer moniter.

Included with the machine, leveling pads, manuals, punches, and dies

Location: Cleves, Ohio
Rigger Will Be Required To Load, Buyers Responsibility

Power: 1500 Watts
Typiclal Range: 100 1500 Watts
Serial Number: 49335
Fanuc Series 16 control



Maximum Workpiece
X: 98.5"
Y: 49.25"
Z: 1.0"
Rapid Traverse X & Y: 1600IPM

Cutting Hours 47,395

Additional information in the photo gallery for this machine

Location: Cleves, Ohio
Rigger Will Be Required To Load, Buyers Responsibility

EUROMAC BX 1000/30

Location: Genoa, NY
Rigger Will Be Required To Load, Buyers Responsibility

MITSUBISHI MD PRO III WIRE EDM

M700 Series Control
15" touch screen
All-Axes Absolute Control System

V350-V AEII Power Supply
DMX-S (Digital Matrix Sensor) Shapes each spark reducing electrode wear
World's first Linear Shaft Drive System XY (UV-Z use ball screws)
AH Fiber Optic servo control (4X faster internal communication speed)
Submerged Machining to 8.7" Deep
Automatic Fluid Level Control
Manual Vertical Machine Tank door
Three Piece Hardened 3-Sided Stainless Work Table
Fine Grain "Dianite" Casting Material
Split Axis Construction (Table Moves in X, Column Moves in Y)
Windows XP Operating System
PM5 Power Master Control Improves Poor Flush Machining up to 50%
Program Input Methods: Keyboard, USB Flash Memory, and Ethernet with FTP standard DC-Servo (Closed Loop) Torque Control Wire Tensioning System
Non-contact, Zero Back-Lash Linear Shaft Motor Drive System (XY)
Linear Motion Guide Ways
All-Axes Absolute Control System
Linear Glass Scale Feedback (X-Y- Axes)

Optical Rotary Encoder Feedback (UV-Z-Axis)
Scrap Wire Processor (Chopper) (Optional)
New 14" AT Annealing Length Improves Threading Reliability Inverter Controlled 16-Step Programmable Flushing
Full Time AEII (Anti-Electrolysis) Power Supply Protection Dielectric Fluid Chiller Standard
Full 1-yr. Warranty with Triple Diamond Partnership Program Auto-Oiler Lubrication System

Location: Genoa, NY
Rigger Will Be Required To Load, Buyers Responsibility

Model A6 ½
190 ton OBI
Serial # 26194
Slide adjustment: 4 - 7/8”
Table: 50.5” w x 35.5” deep x 4” thick; drilled & tapped
Manuals available for this machine based on s.n. obtained from OEM - C-N-B [ Clearing Niagara Bliss ]
Current owner states the press appears to be in excellent condition [ ex. aerospace facility, doing light duty as a hot joggle press]

Location: Fort Worth, Texas
Rigger Will Be Required To Load, Buyers Responsibility

CNC Turning Center Yam (Spectro USA)
Model CK-2
Current owner states this machines runs every day and is good working condition. It is under power for inspection.



Fanuc 11T Control
18.00” Maximum Swing
10.63" Maximum Turning Diameter
22.00" Maximum Turning Length
Tailstock
8-Position Turret
10" 3-Jaw Chuck
2” Bar capacity
Chip Conveyor
s/n E77029
Approx. 128" x 84" x 80" Overall.
All manuals are available.
Parts and service available from Spectro USA

Location: Duncan, South Carolina
Rigger Will Be Required To Load, Buyers Responsibility
Rigging - Approx. $800.00 to remove from building and load onto flat bed truck

Monarch VMC-150 CNC Vertical Machining Center
Model: VMC-150 | Age: 1989 |
SERIAL NO.: 89509



FEATURES:
FANUC 11M CNC CONTROL
40-STATION AUTOMATIC TOOL CHANGER

CAPACITIES:
X-AXIS TRAVEL, TABLE BACK & FORTH 50"
Y-AXIS TRAVEL, SADDLE IN & OUT 36"
Z-AXIS TRAVEL, QUILL UP & DOWN 10"
W-AXIS TRAVEL, SLIDING HEAD UP-DOWN 23"
SPINDLE SPEED, MAX 5200 RPM
SPINDLE TAPER CAT 45
SPINDLE DRIVE MOTOR 20 HP / 15 HP
MILLING FEEDRATES 0.01-400 IPM
POSITIONING SPEED 600 IPM
DIMENSIONS 170" X 161"
HEIGHT 124"
APPROXIMATE WEIGHT 22,000 LBS
APPROXIMATELY 10 TOOL HOLDERS INCLUDED.

The fixture, Haas indexer and control box on the side of the machine are not included. The machine runs every day and is good working condition, it is under power and available for inspection.

Location: Duncan, South Carolina
Rigger Will Be Required To Load, Buyers Responsibility
RIGGING COST - $2800.00 TO RIG OUT OF BUILDING AND LOAD ONTO FLAT BED.

MILLPORT II Precision Surface Grinder
Specifications:
Table Size ................................................. 5-3/4" x 18"
Longitudinal Table Travel ............................. 19"
Cross Saddle Travel..................................... 6-3/4"
Max Work Height ........................................ 12"
Table Speeds (Variable) .............................. 0-70 FPM
Saddle Cross Feeds (Intermittent)................. 0.006- 0.375 IPM
Grinding Wheel Size.................................... 8" x 1/2" x 1 1/4"
Spindle and Motor....................................... 68"H x 50"W x 42"L
Weight...................................................... 2000 Lbs.
Equipped With:

Hydraulic 2 Axis Power Feeds
Splash Guard
Horsepower: 2

Location: Duncan, South Carolina
Rigger Will Be Required To Load, Buyers Responsibility

2004 ATLAS COPCO GA75 SCREW AIR COMPRESSOR

Model GA 75 VSD
Max Bar PSI is 188
Nominal Start Power is 100 KW-HP
The Compressor does need a new contactor to be 100 precent and ready to use.
Never used after putting over $20,000 into the unit which included:
A) Fan Motor $1,560
B)Air Valve selonoid $777
C)Drive motor rebuild $6,305
D)Screws rebuild $12,703

Location: Acworth, Georgia

Grinding Master deburr system
Model MCSB - 1300
51" (1300mm) wide
Two stage, abrasive belt and wire brush type deburring
(2) 30 HP drives
Gear driven conveyor belt, made in Holland, supported by Timesavers International
Manuals
Requires dust collector

Location: St. Louis, MO
Rigger Will Be Required To Load, Buyers Responsibility

2008 Model: LHZ44 (Movable) WUXI YANGTONG MECHANICAL EQUIPMENT COMPANY
Year Built: 2008
Boom Travel: 4000 mm (157.5”)
Boom Travel Speed: 120 to 1200 mm/min. (adjustable from 4.75 inch/per minute to 47.25 inch per minute)
Height/Elevation Stroke of Boom: 4000 mm (157.5”)
Elevating Speed of Boom: 1000 mm/min (up and down 39.375” per minute)
Trolley Travel Speed: 1700 mm/min (forward and backward 67” per minute)
Column Rotation Range: +/- 180 degree (360 degree range with fixed stop)
Boom Wheel Spacing: 1780 mm (70” center to center)

Multi hinged positioning arm allows multiple head orientation and positions allowing for easy adjustment from circumferential and longitudinal welding.
Motorized cross slides allow for 6” side to side, and 6” up/down adjustment of weld heads. (Speed adjustable)
Heated Flux tank and air powered flux delivery to forward flux hopper
Lincoln mini-vac flux recovery
Manipulator wiring and control upgraded to meet CSA.

Current Set-up:
Tandem wire DC/AC

DC source: Lincoln Idealarc
Model: DC 1500
Code: 7828
Serial: AC-417195
Control: Lincoln NA-3N

AC Source: Lincolnweld
Model: AC 1000
Code: 6434-C
Serial: AC 310857
Control: NA-4

Location: Hamilton, Ontario
Rigger Will Be Required To Load, Buyers Responsibility